Coverage: Each pail will cover on average 1,000 sf. This will be greatly affected by how tightly troweled the wear layer is and the last time the surface was rebinded.
Shipping time: One to two days.
Trassig's Playground Poured in Place Rubber Rebinder B™ is the solution to the age old problem of granulation that usually leads to cracks, holes and expensive repairs to the rubber surface. It is designed to replenish your playground safety surfacing with the bonding agents that were lost to UV exposure. It is a one component product that is ready to use without mixing with any other solvents. It is very easy to apply and will ensure your rubber surface will last. The difference between our Rebinder and the Rebinder B™ is that the Rebinder B™ will slightly amber your surface when applied. Some colors are affected more than others. This color change is temporary. Please call your Trassig install specialist for more details.
Note: If you are conditioning a pool or splash pad surface, use the Rebinder instead.
If you are not sure whether you need the Rebinder or Rebinder B to condition your rubber suface,read this article
The Different Stages of Poured In Place Deterioration
How to Recondition Your Poured In Place Surface with Trassig's Rebinder B™
The cheapest way to save your Poured In Place surface at 24 cents per square foot vs. adding another wear layer at $8 to $15 per square foot.
Will not crust or harden your surface if applied properly and at the right time.
Will temporarily amber your surface. This is more visible with brighter colors.
Easy, DIY application. No need to add solvents
When do I apply the Rebinder B™?
You can only rebind your playground surface when it needs to be reconditioned. Rebinding prematurely can harden the Poured In Place system. We tell our clients to do the "Shuffle test" which means scraping your feet on the rubber surface to see if you can easily dislodge the granules. It's very important to ONLY Rebind when you see loose granules.
Look for a sunny day above 60 degrees. If it is going to rain within four hours after applying, do not rebind.
Step 1: Use a leaf blower to remove loose granulated rubber and other debris from area. If necessary, use a power washer with a wide angle nozzle and binder friendly detergent to sanitize the surface. Make sure your surface is COMPLETELY dry before continuing. Check under equipment for possible excess water and moisture
Step 2: Lay down a tarp to avoid splashing and use a paddle mixer to thoroughly mix the Rebinder B™ in the pail before use. It is necessary to mix Rebinder B™ before use.
Step 3: Pour Rebinder B™ into drip pan. Do not mix with other products or solvents.
Step 4: Use a cheap paint roller to equally distribute Rebinder B™ on your poured in place surface because you will be throwing it away after installation.
Step 5: Apply pressure when applying Rebinder B™ in order to make sure the coat is even and sufficient. Go over each area only one time. Do not treat Rebinder B™ like paint. Multiple layers will harden your surface.
Step 6: Even though Trassig’s Rebinder B™ is fast curing, secure area and allow 24 hours before use after application. If it rains 4 hours or more after application the Rebinder B™ will not be affected, but it cannot rain during the application of the Rebinder B™ for it to properly cure.
Watch our installation video here for an example and more information:
Description Our Trassig ET 55 toddler friendly turf meets all safety standards set by ASTM and CPSC, including standards regulating toxicity and flammability. Toddler friendly means that the yarn on...
DESCRIPTION Our Rubber Surface Base Layer Binder is a polyurethane adhesive that is the best when working with buffings or base layer rubber for playground surfacing and track and field surfacing. Our 2...
DESCRIPTION Our Rubber Surface Base Layer Binder is a polyurethane adhesive that is the best when working with buffings or base layer rubber for playground surfacing and track and field surfacing. Our 1...